An AI takes the noise out from behind a voice, then the speech is made clearer and the loudness even, on Snipmill's server.
Settings
Good to know
The AI noise remover, and where it runs
- Where it runs
- What to expect: By an AI model on Snipmill's server, on a computer, phone or tablet
- What is sent
- What to expect: The sound alone, 48 kHz mono AAC at 64 kbps, when you press Start; a video's picture isn't sent
- Other voices or music behind the speaker
- What to expect: Turned down, but not always removed: play the result
- Sound it keeps
- What to expect: 48 kHz, in mono; the cleaned sound comes back as Opus at 64 kbps
What noise removal does to your recording
- Noise
- What happens: With Noise on, the sound goes to Snipmill's server, where the AI model takes out what isn't the voice; the cleaned sound comes back and the server deletes what was sent
- Low rumble
- What happens: Everything under 80 Hz is cut (with Voice on Clearer)
- Voice
- What happens: With Clearer: gentle compression, so loud and soft words come closer, and +3 dB around 3 kHz
- Loudness
- What happens: With Even: −16 LUFS for the whole file, as one steady change worked out from a measuring pass, with peaks under −1.5 dBTP
- Length, mono or stereo
- What happens: The length is kept; with Noise on the result is mono
- Format
- What happens: Your file's own: MP3 stays MP3, M4A and AAC come out as M4A, WAV (16-bit), FLAC and OGG stay; Opus comes out as OGG (Vorbis); anything else as MP3. MP3 and M4A at 192 kbps
- Video
- What happens: The picture is copied as it is when it is H.264 or HEVC, else encoded again as H.264; the sound goes back in as AAC at 192 kbps, in an MP4
Which setting to pick
Noise, Remove or Keep: Remove runs the AI noise remover on the whole file. Keep it for a recording without noise, where only the voice or the level needs work. Voice, Clearer or As is: Clearer cuts rumble under 80 Hz, brings loud and soft words closer and adds +3 dB around 3 kHz. Loudness, Even or As is: Even sets the whole file to −16 LUFS, the level Apple asks podcasts to keep (it writes it as −16 LKFS, the same scale). Turn it off to keep a recording's own level.
What people clean
A 3-minute voice memo recorded next to an air conditioner, as M4A: the hum is taken out from behind the voice, and it comes back as an M4A of about 4.2 MB. A 20-minute phone video of an interview with traffic outside, cleaned on a laptop in Chrome: the traffic is taken out, the H.264 picture is copied as it is, and the voice comes out at −16 LUFS. A vlog recorded in a busy market: the crowd behind the voice is turned down, but other voices are speech too, so some can stay; play the result before you post it.
What goes to our server
How to remove background noise from audio
Open this page on a computer, phone or tablet. The noise is taken out by an AI model on Snipmill's server; the sound comes back and the file is made in your browser. Choose the recording or video: MP3, M4A, WAV, FLAC, OGG, Opus or AAC, or a video, up to 2 GB in Chrome or Edge on a computer, 1 GB in Safari on a Mac and 500 MB on a phone or tablet, up to 30 minutes long. Up to 10 files at once get the same settings. Leave Noise on Remove. Voice on Clearer cuts rumble under 80 Hz and lifts the speech; Loudness on Even brings the whole file to −16 LUFS. Press "Clean up sound" in the bottom bar and play the result. A sound file comes back in its own format, a video as an MP4 with the same picture; your original stays as it was.